GOVERNMENT OF
MINISTRY OF COMMERCE AND INDUSTRY
DEPARTMENT OF COMMERCE(SUPPLY DIVISION)
DIRECTORATE GENERAL OF SUPPLIES AND DISPOSALS
OFFICE OF THE DIRECTOR OF SUPPLIES AND DISPOSALS
NEW C.G.O.BLDG, 5&6TH FLOOR, S.W.WING
NEW MARINE LINES, MUMBAI-400020.
REGD.A.D. FAX NO.022-2080 686.
TEL NO.2203 3950
RATE CONTRACT NO.MB-1/RC-13110600/042004/APM/2004-2005
RIS/ 0094/COAB Dt.30.4.2004
M/s.RIS Engineering Co.,
535,
Mumbai 400002.
Sub : Rate contract for supply of Ammonia Printing Machine valid from
1.5.2004 to 30.4.2005.
Ref : i) This office T/E No. MB-1/RC-13110600/042004/APM/2004-2005
opened on 21.1.2004.
ii) Your Qtn. No. GF-1/2004/70303 dt. 3.1.2004 and subsequent letter
No. GF-1/2004/70364/RC-16 dt. 23.3.2004.
.
Dear Sirs,
You are hereby informed that your above referred tender read with subsequent letters mentioned above for the stores specified in the schedule annexed has been accepted. This rate contract will be governed by the terms and conditions brought in the form No.DGS&D-1001. The Rate contract and the schedules annexed hereto shall be the sole repository of this Rate contract/transactions.
Please acknowledge receipt of the R/C.
SCHEDULES ANNEXED:
1. Schedule A: Description of stores, prices, duties/taxes.
NOTE: The General Terms and
Conditions governing the Rate contract and special instructions to consignees have
been incorporated in a separate booklet form DGS&D-1001. This booklet will
be a saleable document at the cost of Rs.50/- each. Copies of form
DGS&D-1001 are being made available for sale through DGS&D,
Yours faithfully,
(R.K. GUPTA)
ASSTT. DIRECTOR OF SUPPLIES
FOR & ON BEHALF OF THE PURCHASERS NAMED
IN THE SCHEDULE FORM DGS&D-1001.
-2-
.MB-1/RC-13110600/042004/APM/2004-2005
RIS/ 0094/COAB
COPY TO:
1. The Dy Controller of Accounts, Deptt. Of supply, Sir Shivsagar Ramgulam Marg, Ballard Estate, Mumbai. (Through Authentication).
This issues with the approval of Competent Authority.
2.
Director of Supplies & Disposals, Shastri bhavan,
3. Director of Supplies & Disposals, 6, Esplanade East, Kolkata-7000 69.
4. Director General of Supplies & Disposals, N.I.Bldg, 5 sansad marg, New Delhi-110001.
5. Dy. Director General (QA),Southern Zone, Shastri bhavan, 26 Haddows road, Chennai-600 006.
6. Dy. Director General (QA),West Zone, Aayakar bhavan, Annexe, New Marine Lines,Mumbai-400020.
7. Dy. Director General (QA),East Zone,Nizam palace, 2nd M.S.bldg, 8th floor, 234/4 Acharya J.C.Bose road, Kolkata-7000 20.
8. Dy. Director General (QA), North zone, 4th floor, N.I.Bldg, 5 sansad marg,,New Delhi-110001.
9.
Insp. Authority : A.D.G.
(QA),DGS&D, N.I.Bldg, 5 sansad marg,
10. Con. Audit.
11. RC/CDN Section.
12.
MIS Cell-4/MIS-9/MIS-10 DGS&D.,
13. Computer section.
14. Master folder.
15. All D.D.Os as per mailing list maintained by DGS&D.
16. Income Tax Officer Ward No. 14(2)(1) Mumbai
Firms permanent A/C No. PAN :AAEPSO268G
17. Railway Liaison Officer, Railway Board, DGS&D, 5 sansad marg, Parliament Street, New Delhi.
18.
Director of Quality Assurance,
Mumbai/Chennai/Kolkata/New
19.
ADG(Q.A.), DGS&D.,
20.
M/s. RIS Engg.
(R.K. GUPTA)
ASSTT. DIRECTOR OF SUPPLIES
FOR DIRECTOR OF SUPPLIES AND DISPOSALS
-3-
SCHEUDLE A
RATE CONTRACT NO. .MB-1/RC-13110600/042004/APM/2004-2005
RIS/ 0094/COAB Dt.30/4/2004
1. ADVANCE RATE CONTRACT NO : NIL
2. Name and full address of the : M/s. RIS Engineering Co.,
firm
535,
Mumbai 400002
Tel No.(O) 22017769
(F) 24147508 , 24149483
Tele Fax No. 24147508
Gram : EXPOMACHIN (Kalbadevi) Mumbai-02
E-mail : risengg@vsnl.net.
3. Name and full address of the
: M/s. RIS Engg.
manufacturer Industrial Estate, Block C-7 ,
Ground floor,
Wadala, Mumbai -400031.
4. Validity of Rate contract : From 1.5.2004 to 30.4.2005
5. Description of items, specification , unit and rates.
Item No. Model Description of Stores Unit Rate per Unit
No.
1&3 A-1 Ris Continuous Printer only Table To No. Rs. 16,800/-
1(a) Model i.e. without stand but complete (Each) (Rs.Sixteen thousand
with a separate vertical wooden. Eight hundred only)
Ammonia Developing Box, and
Fitted with 12 Volts D.C. Fractional
H.P. variable speed reversible gear motor,
Exhaust cooling fans or either side and
Generally as per literature enclosed
herewith with a light source of :
1x140/03 Watts capacity each
(total 140 watts) Super Actinic Tube,
with a speed range of 0 to 6 ft.
(0 to 180 + 20 Cms.) per minute.
Contd/--4
-4-
1&3 A Ris Continuous Printer only Table Top No. Rs. 18,480/-
1(c) Model i.e. without stand but complete (Each) ( Rs.Eighteen thousand
with a separate vertical wooden. Four hundred Eighty
Ammonia Developing Box, and only)
Fitted with 12 Volts D.C. Fractional
H.P. variable speed reversible gear motor,
Exhaust cooling fans or either side and
Generally as per literature enclosed
herewith with a light source of :
2x140/03 Watts capacity each
(total 280 watts) Super Actinic
Tubes, with a speed range of
0 to 12 ft. (0 to 360 + 20 Cms.)
per minute.
1&3 B Ris Continuous Printer only Table Top No. Rs. 20,100/-
1(d) Model i.e. without stand but complete (Each) (Rs. Twenty thousand
with a separate vertical wooden one hundred only)
Ammonia Developing Box, and
Fitted with 12 Volts D.C. Fractional
H.P. variable speed reversible gear motor,
Exhaust cooling fans or either side and
Generally as per literature enclosed
herewith with a light source of :
3x140/03 Watts capacity each
(total 420 watts) Super Actinic
Tubes, with a speed range of
0 to 16 ft. (0 to 480 + 20 Cms.)
per minute.
The machines offered above will have a speed
range of 0 to 360 + 20 Cms. Or 0 to 480 + 20
cms. Per minute depending on the light source and
will be without stand but complete with separate
vertical wooden Ammonia Developing chamber
required under item No. 3 of your tender.
The salient features and advantages of the machine
quoted under item No.1 and 3 above, specified on
separate sheet is enclosed for your reference and
record, under Annexure A-I & A-II.
Contd/--5
-5-
2A A-1 Ris Continuous Printer and No. Rs. 31,500/-
2(a) Developer (combined) machine (Each) (Rs. Thirty One
Complete with stand and fitted with Thousand Five 12 Volts D.C Fractional H.P.variable hundred only)
speed reversible gear motor, exhaust
cooling fans on either side and generally
as per literature enclosed herewith a light
source of :
1x140/03 Watts capacity each (total
140 Watts) Super Actinic Tubes, with
a speed range of 0 to 6 ft. (0 to 180 + 20 cms)
per minute.
The machine offered above will have a speed
range of 0 to 360 + 20 cms. per minute
depending on the light source and the machine
will have either a Rexine or Rubber Developing Belt
The Salient Features and advantage of the machine
quoted under item No.2(A) above,
Specified on separate sheet on Annexure B-I & B-II.
2A A Ris Continuous Printer and No. Rs. 33,390/-
2(c) Developer (combined) machine (Each) (Rs. Thirty Three
Complete with stand and fitted with Thousand Three 12 Volts D.C Fractional H.P.variable hundred ninety only)
speed reversible gear motor, exhaust
cooling fans on either side and generally
as per literature enclosed herewith a light
source of :
2x140/03 Watts capacity each (total
280 Watts) Super Actinic Tubes, with
a speed range of 0 to 12 ft. (0 to 360 + 20 cms)
per minute.
The machine offered above will have a speed
range of 0 to 360 + 20 cms. per minute
depending on the light source and the machine
will have either a Rexine or Rubber Developing
Belt.
The salient features and advantage of the
Machine quoted under item No.2(A) above,
Specified on separate sheet on Annexure
B-I & B-II.
Contd/--6
-6-
2A B Ris Continuous Printer and Developer No. Rs. 36,000/-
2(d) (combined) machine complete with stand (Each) (Rs. Thirty Six
fitted with 12 Volts D.C. Fractional Thousand only)
H.P. variable speed reversible gear motor
exhaust cooling fans on either side and generally
as per literature enclosed herewith a light
source of :
3x140/03 Watts capacity each (total
420 Watts) Super Actinic Tubes, with
a speed range of 0 to 16 ft.(0 to 480 + 20 cms.)
per minute.
The machine offered above will have a speed
range of 0 to 480 + 20 cms. per minute
depending on the light source and the machine
will have either a Rexine or Rubber Developing
Belt.
The salient features and advantage of the
Machine quoted under item No.2(A) above,
Specified on separate sheet on Annexure B-I & B-II
2B A Ris Continuous Printer and Developer No. Rs. 72,750/-
2(f) (Combined) Mark-II Machine generally (Each) (Rs. Seventy Two
as per literature enclosed herewith with a Thousand Seven
light source of : hundred Fifty only)
6 x 140/03 watts capacity each(total 840 watts)
Super Actinic Tubes with a speed range of
0 to 25 ft.(0 to 750 + 20 cms) per minute.
The salient features and advantages of our Mark-II
Machine specified on separate sheet on Annexure
C-I & C- II.
2(g) C Ris Continuous Printer and Developer No. Rs.1,35,000/-
(Combined) Mark-II Machine generally (Each) (Rs.One lakh
as per literature enclosed herwith with a Thirty Five thousand light source of : only.
1 x 3000 watts capacity High Pressure . Mercury Vapour Lamp with a speed range
of 0 to 40 ft. ( 0 to 1200 + 20 cms.)
per minute.
The salient features and advantages of our Mark-II
Machine specified on separate sheet on Annexure
C-I & C- II.
Contd/---7
-7-
NOTE :
1.(a) Above prices
are including installation and commissioning of machine any where in
(b) Firm shall supply a catalogue/leaflet/operation/maintenance/manual etc. alongwith each machine free of cost.
--------------------------------------------------------------------------------------------------------------------
6. Terms of Delivery : F.O.R. Mumbai basis only insured upto destination
And duly installed free of cost with freight to pay.
7. Excise duty : Excise duty charged extra as applicable at the time
of supply.
8. Sales Tax : S.T., T.O.T., Sc. On S.T./C.S.T. payable extra
With form H or D or VAT as and when
applicable, payable extra.
9. Delivery period : The machines will be ready for delivery/despatch
from Mumbai within the period specified below for
the respective machines, after receipt of your/or
consignees clear acceptable order subject to
DGS&D force majeure clause.
Item 1 & 3 : Ris Continuous Printer
Only Table Top Model
In about Ύ weeks subject to a
Maximum of 3 machines per month.
Item 2(A): Ris Continuous Printer and
Developer(combined)machine
In about 4/6 weeks subject to a
maximum of 2 machines per month.
Item 2(B): Ris Continuous Printer and
Developer (combined) Mark-II
Machine
In about 6/8 weeks subject to one machine every 2 months.
10. Monetary Limit : Rs. 5 lakhs
11. Slab discount : NIL
Contd/--8
-8-
12. Prices : Prices are firm and final and are inclusive of
packing/forwarding and transit insurance charges upto destination.
13. Minimum quantity : Not applicable
in Single Supply Order
14. Status of R/C holding firm : S.S.I.
15. Payment terms : 98% payment on proof of inspection and despatch
(Provisional receipt) balance 2% on receipt of stores
by consignee in full and good condition. Also see
general terms and conditions in form No. DGS&D-
1001.
16. Paying Authority : Dy. Controller of Accounts,
Deptt. of Supply, Mumbai
17. Inspection Authority : A.D.G.(Q.A.), DGS&D.,
Jeevan Tara bldg.
5,
Sansad Marg,
18. Quality Assurance Officer : Director of Quality Assurance, Mumbai
Or his authorized representative of the area concerned.
19. Place at
where the stores are : M/s. RIS Engg.
to be tendered for inspection Block C-7 , Ground floor,
Wadala, Mumbai -400031.
20. Warranty/Guarantee : D.G.S.&D. Standard Warranty/Guarantee Clause as
per Clause -18 of Form No. D.G.S.& D.-1001 will
be applicable for subject Rate Contract. However, Warranty/Guarantee Clause is not applicable for following items :
i) Parts made of Cloth, Rexine, Rubber Plastics and fibres.
ii) Glass Cylinder, Actinic Tubes and HPMV Lamps.
iii) All Electrical and Electronic Components.
NOTE : The supplier must ensure that R/C No. & Date should be indicated on each bills submitted to Accounts for payment.
(R.K. GUPTA)
ASSTT. DIRECTOR OF SUPPLIES
FOR DIRECTOR OF SUPPLIES AND DISPOSALS
SCHEDULE B
ANNEXURE A-I
RIS
CONTINUOUS PRINTER ONLY TABLE TOP MODEL AQUOTED UNDER ITEM NO.
1 & 3
1. Max effective width of - 114 cms. Width in cut sheets
Paper which can be fed and rolls with cutting arrangement on feed
Sheet and rolls with cutting board.
Arrangement
2. Light Source - Model A-1 1 x 140/03 watts
Super Actinic Tubes
Model A : 2 x 140/03 watts
Super Actinic Tubes
Model B : 3 x 140/03 watts
Super Actinic Tubes
Tube light easily removable for periodic cleaning and/or replacement.
3. Linear Speeds - Model A-1 : 0 to 180 + 20 cms./min.
Model A : 0 to 360 + 20 cms./min.
Model B : 0 to 480 + 20 cms./min.
4. Printing & Developing - ----------
Speed
5. Developing Unit - Vertical Wooden Ammonia Developing
Chamber. App. overall dimensions 21 cms.
Deep x 24 cms. Wide x 120 cms. Height.
All dimension + 20mm.
6. Drawings - Literature showing drawing enclosed with
the quotation.
7. App. overall dimensions - Length 165/171 cms. Height with
Legs 37/42 cms. Width with feed board
47/52 cms.
8. Glass Cylinder - Borosilicate Glass Cylinder.
9. Cooling Device - Exhaust cooling axial fan provided on either
side.
Contd..2/
-2-
ANNEXURE A-I
10. Details of body constructions - Sheet metal body fabricated from C.R.C.A.
And process of painting sheets 0.7/1mm thick duly spray painted. All
metallic parts including sheet metal body
panel etc. painted with coat of red oxide and
then spray painted.
11. Drive mechanism - Electronically controller stepless and
Continuously variable.
13. Details of Drive - F.H.P. 12 Volts magnet type D.C. reversible
geared motor either DENSO INDIA LTD.,
or any other suitable make with prior approval.
14. Electric Supply - 220/230 Volts A.C. Single phase
15. Power Input - Model A-1 : App. 350 watts 4.5 amps
Model A : App. 400 watts 5.0 amps
Model B : App. 600 watts 6.0 amps.
16. Overall Power Factor - Power factor of whole machine will be
maintained at 0.85 min.
17. Printing Belts - Canvas rubberised belts.
18. Developing Belt - ----
19. Developing unit - Refer item No.5 above.
------------------
ANNEXURE B-1
SPECIFICATION
OF AMMONIA PRINTING MACHINES QUOTED AS PER
FORMAT ADDITIONAL REQUIREMENT
Ris Continuous
Printer & developer (combined) Machine quoted under
Item 2 A
1. Max effective width of - 114 cms. Width in cut sheets
Paper which can be fed and rolls with cutting arrangement on feed
Sheet and rolls with board.
Cutting arrangement
2. Light Source - Model A-1 : 1 x 140/03 watts
Super Actinic Tubes
Model A : 2 x 140/03 watts
Super Actinic Tubes
Model B : 3 x 140/03 watts
Super Actinic Tubes.
Tube light easily removable for periodic
cleaning and/or replacement
3. Linear Speeds - Model A-1 : 0 to 180 + 20 cms./min.
Model A : 0 to 360 + 20 cms./min.
Model B : 0 to 480 + 20 cms./min.
4. Printing & Developing - Printing & Developing Speed
Speed synchronised.
5. Developing Unit - Fabricated from Stainless Steel with
temperature controlled by a heater
working in conjuction with an automatic
energy regulation switch and a indicator
Lamp
6. Drawings - Literature showing drawing enclosed with
the quotation.
7. App. overall dimensions - Length 180/185 cms. Height with
Stand 125/130 cms. Width with feed board
65/73 cms.
Contd..2/
-2-
ANNEXURE B-I
8. Glass Cylinder - Borosilicate Glass Cylinder.
9. Cooling Device - Exhaust cooling axial fan provided on either
side.
10. Details of body constructions - Sheet metal body fabricated from C.R.C.A.
And process of painting sheets 0.7/1mm thick duly spray painted. All
metalic parts including sheet metal body
panel etc. painted with coat of red oxide and
then spray painted.
11. Drive mechanism - Electronically controlled stepless and
Continuously variable.
printing drive roller.
13. Details of Drive motor - F.H.P. 12 Volts magnet type D.C. reversible
geared motor either DENSO INDIA LTD., or any other suitable make with prior
approval.
14. Electric Supply - 220/230 Volts A.C. Single phase
15. Power Input - Model A-1 : App. 1400 watts 7.0 amps.
Model A : App. 1500 watts 8.0 amps.
Model B : App. 1650 watts 9.0 amps.
16. Overall Power Factor - Power factor of whole machine will be
maintained at 0.85 min.
17. Printing Belts - Canvas rubberised belts.
18. Developing Belts - Canvas rubberised belts or rexine developer
belt.
19. Developing Unit - Refer to item No.5 above.
--------
ANNEXURE A-II
RIS
CONTINUOUS PRINTER ONLY TABLE TOP MODEL A-1, A & B
ITEM NO. 1 & 3
Specification Deviation
a) Overall size of the - Length 165/171 cms NIL
machine Height with legs
37/42 cms.
Width with feed
Board 47/52 cms.
b) Effective width of paper - 114 cms. NIL
which can be fed :
112 cms to 120 cms.
c) Printing speed range
i) 100 cms/min. - i) Model A-1 : i)Model A-1:
0 to 180 + 20 cms/min. More than required
ii)200 cms/min. ii) Model A: ii)Model A :
0 to 360 + 20 cms./min. More than required
iii) 300 cms/min. iii)Model B : iii) Model B :
0 to 480 + 20 cms./min. More than required
d) Drive Mechanism: - Electronically NIL
Infinitely variable with controlled and
Reversing arrangement infinitely variable
with reversing
arrangement.
e) Light Source: - i) Model A-1: NIL
i) One tube of 140 watts One Super Actinic tube
each. of 140/03 watts.
ii) Two tubes of 140 watts ii) Model A :
each Two Super Actinic tubes
iii) Three tubes of 140 watts of 140/03 watts each.
each. iii) Model B :
Three Super Actinic tubes
of 140/03 watts each.
f) Main supply :230 V + 10% - 220/230 V. 50 HZ NIL
50 HZ. Single phase, A.C. Single phase, A.C.
Supply , Power factor 0.85 Supply, Power factor
minimum Minimum 0.85
contd 2/
-2-
ANNEXURE A-II
g) Type of mounting - Table Top mounting NIL
h) Cooling device, if any - Exhaust cooling Axial NIL
fans provided on
either side.
i) Space required for - App. 260 cms. X 130 cms. NIL
working/operating
j) Details of main body - Sheet metal body NIL
construction, fabricated from
materials etc. and finish C.R.C.A. sheets,
0.7/1mm thick duly
Spray painted.
k) HP. of motors and their - Drive motor App. 12 There are
IS Specification Volts D.C geared different
IS:996/79 with Amdt. Motor either DENSO specifications
1 & 2 INDIA LTD., for different
Or any other suit- types of
able make with motor
prior approval.
l) Cutting Device - Cutting arrangement NIL
provided on feed
platform
m) Process of painting - All metallic parts including NIL
Sheet Metal Body Panel, etc.
Painted with coat of Red oxide
And then spray painted.
n) Total power input - i)Model A-1: NIL
Total current required App. 350 watts 4.5 Amps
ii) Model A:
App. 400 watts 5.0 Amps
iii) Model C :
App. 600 watts
o) Printing cylinder - Borosilicate glass NIL
cylinder
---------------
(Annexure C)
i) Size of the Chamber - Approximate over all NIL
dimensions 21 cms.
Deep x 24 cms. Wide x
120 cms. Height. All
Dimensions + 20 mm.
ii) Arrangement for opening - Vertical chamber to NIL
and closing of the be hung from a wall
chamber with front opening
at the lower end.
iii) Materials of chamber - Plywood NIL
iv) Thickness of the - Thickness of plywood NIL
material used in side walls will be 7/8 mm
fabrication of
developer Tank.
v) Finish of the chamber - Painted from outside NIL
vi) Details of the - Vertical chamber NIL
provision for fast ensures quick
developing and development as
evaporation of ammonia Ammonia Gas tends
to rise.
vii) The body and parts coming - The developing A Stainless
in contact with Ammonia chamber is fabricated steel chamber
should be of anticorrosive from plywood, which will be exor-
material and preferable of is not affected by bitantly costly
stainless steel ammonia. However, as such the best
a plastic dish which is also alternative material
not affected by ammonia which is wood is
is provided for keeping made use of.
ammonia liquid
-------------------
ANNEXURE C - I
RIS CONTINUOUS
PRINTER AND DEVELOPERS (COMBINED) MARK II MACHINE
QUOTED ITEM 2(B)
1. Max effective width of - 108 cms. Width in cut sheets
Paper which can be fed and rolls with cutting arrangement on feed
Sheet and rolls with board.
Cutting arrangement
2. Light Source - Model A : 6 x 140/03 watts
Super Actinic Tubes
Model C : 1 x 3000 watts
H.P.M.V. Lamp
Tube Lights & H.P.M.V. Lamps easily removable for periodic cleaning and/or replacement.
3. Linear Speeds - Model A : 0 to 750 + 20 cms/min.
Model C : 0 to 1200 + 20 cms/min.
4. Printing & Developing - Printing & Developing speed
Speed synchronised.
5. Developing Unit - Fabricated from stainless steel
With temperature controlled by two heaters
working alternatively in conjunction with
thermostat and complete with indicator
Lamps.
6. Drawings - Literature showing drawing enclosed with
the quotation.
7. App. overall dimensions - Length 180/185 cms. Height 148/152 cms.
Width with feed board 90/96 cms.
8. Glass Cylinder - Borosilicate Glass Cylinder.
9. Cooling Device - Model A : Cooling of glass Cylinder
achieved by exhausting hot air from the
glass cylinder by means of exhauster driven
by directly mounted 1/4 H.P. Single phase
A.C. motor. The tube light will not operate
unless the exhauster starts.
Contd 2/
-2-
ANNEXURE C - I
Model C : Cooling of glass Cylinder
achieved by forced circulation of air in the
glass cylinder by means of combined
exhauster and blower driven through a V belt by 1/2 to 1 H.P. Single phase A.C. motor. The motor works automatically through thermostatic temperature control inside the glass cylinder.
10. Details of body constructions - Sheet metal body fabricated from C.R.C.A.
And process of painting sheets 0.7/1mm thick duly spray painted. All
metallic parts including sheet metal body
panel etc. painted with coat of red oxide and
then spray painted.
11. Drive mechanism - Electronically controlled stepless and
continuously variable.
13. Details of Drive motor - Drive motor 1/6 or 1/4 H.P.D.C.B.S.
170 Exhauster/ Blower motor 1/4 H.P.
(with tube light machine) or 1/2 to 1 H.P.
With H.P.M.V. Lamp machine. A.C. Single phase B.S. 5000 part II. For above two drive motors as per certificate provided by manufacturer.
14. Electric Supply - 220/230 Volts A.C. Single phase
15. Power Input - Model A : App. 3000 watts 20 amps.
Model C : App. 6500 watts 36 amps.
16. Overall Power Factor - Power factor of whole machine will be
maintained at 0.85 min.
17. Printing Belts - Canvas rubberised belts.
18. Developing Belts - Canvas rubberised belt.
19. Developing unit - Refer to item No.5 above.
--------
ANNEXURE C-II
RIS CONTINUOUS
PRINTER AND DEVELOPERS (COMBINED) MARK II
MACHINE ITEM 2(B)
Specification Deviation
a) Effective width of paper - 108cms.(Throat For your information
which can be fed :112 Cms. Width 112 cms.) 108 cms.is sufficient
to 120 cms. Because the width of
Standard ammonia senstised
Roll is only 102 cms.
b) Printing speed - i)Model A:0 -750 + Nil
20 cms./min.
ii) ModelC: 0-1200
+ 20 cms/min.
c) Drive Mechanism - Electronically Nil
controlled and
infinitely variable
with reversing
arrangement.
d) Light Source -
1). 6 x 140 watts i)Model A: 6 super Nil
Actinic Tubes of
140/03 watts each
2) H.P.M.V. Lamp - ii)ModelC : 1H.P.M.V.
Lamp of 3000 watts
e) Main Supply - 220/230 V 50 HZ Single Nil
230 V + 10% 50 HZ, phase, A.C. Supply
Single phase ,A.C.supply Power factor minimum
Power factor minimum 0.85 0.85
f) Overall size of the - Length 180/185 cms Nil
machine Height with Stand:
148/152 cms.
Width with feed
Board : 90/96 cms.
g) Cooling device, if any - ModelA:Cooling of Nil
glass cyclinder achieved
by exhausting not air
from the glass cyclinder by
means of exhauster driven by directly
mounted Ό H.P. single phase A.C.
motor. The exhauster also exhausts Air
from where the papers come out duly
Contd..2..
-2-
ANNEXURE C-II
developed from under the glass
cylinder and also from lower portion
of the machine where chokes are fitted
The tube lights will not operate unless
The exhauster starts.
Model C: Cooling of glass cylinder achieved
By forced circulation of Air in the glass
Cylinder by means of combined exhauster
& blower driven through Vbelt by ½ to
1 H.P.single phase A.C.motor. The Exhauster
also Exhaust air from where the papers come out
duly developed, from under the glass cylinder and
also from lower portion of the machine where transformer is located . The motor works automatically through thermostatic temperature control inside the glass cylinder.
h) Space required for - App. 315 cms. X 210 cms. Nil
working
i) Material used for - Developing Unit Nil
fabrication of fabricated from
Developer tank Stainless Steel
j) Duct size of ammonia - App. 115/125 mm. diameter Nil
exhaust - mm
k) Materials and thickness - C.R.C.A. Sheets of Nil
of sheet constituting body about 0.7/1 mm thick
l) Process of painting - All metallic parts Nil
including sheet metal
body panel etc. painted
with coat of red oxide
and then spray painted.
m) Type make and HP of - Drive motor 1/6 or There are
electric motors and 1/4 H.P.D.C. B.S. different
there IS specification. 170 Exhauster/Blower specifications
Motor to confirm to motor, 1/4 H.P.(with for different
IS:996/79 with Amdt. Tube light machine) types of motors.
No. 1 & 2. or 1/2 to 1 H.P.(with B.S. 5000 pt.-II
H.P.M.V. Lamp machine) is equivalent to
A.C. single phase B.S. IS:996/79.
5000 part II
Contd 3/
-3-
ANNEXURE C-II
n) Details of controls & - 1. Master ON/OFF Switch Nil
meters provided 2. Speed Control knob
3. ON/OFF Switch &
reversing switch for
drive motor.
4. Blower ON/OFF Switch
5. Heater Switch
6. Tube light switch
7. Heater indicator
8. Ammonia Control Value
o) Total power input, - 1) Model A : App. 3000 watts Nil
total current required 20 Amps.
2) Model C : App. 6400 watts
36 Amps.
p) Printing cylinder - Borosilicate glass Nil
material & thickness cylinder
q) Any other important - Machine cabinet type. Therefore Nil
feature operator can work in standing
position. Machine provided with
Ammonia storage tank. Machine
provided with tool box containing
oil can, screw driver, spanners,
plastic funnel.
******************************************************************************